{"product_id":"96-angled-l-track-anodized-finish-4-pack","title":"96\" Angled L-Track | Anodized Finish | 4-Pack","description":"\u003ch2\u003e96\" Angled Anodized Aluminum L-Track - 4-Pack\u003c\/h2\u003e\u003cp\u003eThis 96\" rail is the angled version of standard L-track: the edges slope away from the anchor slots so wheels, casters, and pallet jacks roll across it instead of catching on a square shoulder. That makes it a natural fit in pickup beds, toy haulers, and enclosed trailers where cargo has to move over the track to get where it is going.\u003c\/p\u003e\u003cp\u003eAnchor slots run the full length of the rail, so a snowmobile, a lawn tractor, a utility cart, or a stack of construction material can each be tied down at whatever point suits it.\u003c\/p\u003e\u003ch3\u003eWhat the Anodizing Buys You\u003c\/h3\u003e\u003cp\u003eThe extrusion is 6061-T6 aluminum, which is light and corrosion resistant on its own. Anodizing goes further: the finish is grown into the surface of the metal rather than sprayed onto it, so there is no coating to chip or peel back from an edge. What you get is a harder face that shrugs off scuffs from loading and unloading, plus better tolerance for sun, road spray, and repeated washdowns than bare aluminum.\u003c\/p\u003e\u003ch3\u003eMounting\u003c\/h3\u003e\u003cp\u003eMounting holes are pre-drilled on 4\" centers down the full run, sized for 1\/4\", 6mm, or #12 hardware. A through-bolt with a nut and washer - plus a dab of thread locker - is the most dependable joint. Lag screws or self-drillers into wood or sheet metal will hold, but do not expect bolted-joint strength from them.\u003c\/p\u003e\u003cp\u003eHardware is sold separately - the \u003ca href=\"\/products\/airline-style-track-fastener-pack-1-1-2-bolts-w-nut-washer-10-pk\"\u003e1-1\/2\" bolt, nut, and washer pack\u003c\/a\u003e is the usual pairing.\u003c\/p\u003e\u003cp\u003eIf the length or hole spacing does not suit your layout, the rail cuts cleanly with a carbide-tipped blade in a hacksaw or chop saw, and you can add holes with a carbide countersink bit. Read the welding note below before you take any heat to it.\u003c\/p\u003e\u003cp\u003eEnd caps are available for this profile if you want to close off the cut ends and tidy up the installation.\u003c\/p\u003e\u003ch3\u003eDo Not Weld It As-Is\u003c\/h3\u003e\u003cp\u003eLeave the anodizing on and this rail will not weld properly. The finish behaves as an insulator and contaminates the puddle, which leaves a weak and unpredictable joint. If your install genuinely calls for a weld, grind the anodizing off the weld zone and a margin around it first and weld to bare aluminum.\u003c\/p\u003e\u003ch3\u003eHow Much Will It Hold?\u003c\/h3\u003e\u003cp\u003eWe do not publish a single working load limit for the rail, because an installed track is only as strong as the fasteners you picked and the structure you anchored into. The extrusion is made to be at least as strong as the fittings and straps we sell to go with it, which puts the responsibility on the install. If you are unsure what your floor or wall will take, ask your trailer or vehicle manufacturer, and read WSTDA T-5, section 3.4.\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e 96\"\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProfile:\u003c\/strong\u003e Angled edge, low-obstruction\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e 6061-T6 aluminum, anodized finish\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting holes:\u003c\/strong\u003e 4\" centers\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible hardware:\u003c\/strong\u003e 1\/4\", 6mm, or #12 fasteners\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e 4 rails\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFinish the System\u003c\/h3\u003e\u003cp\u003eTrack on its own does not secure anything. Pair it with single- or double-stud \u003ca href=\"\/collections\/l-track-stud-fittings-accessories\"\u003eL-track fittings\u003c\/a\u003e, \u003ca href=\"\/collections\/l-track-straps\"\u003eL-track straps\u003c\/a\u003e that clip straight into the slots, or a \u003ca href=\"\/collections\/cargo-net\"\u003ecargo net\u003c\/a\u003e for loose gear. Pre-built \u003ca href=\"\/collections\/l-track-kits\"\u003eL-track kits\u003c\/a\u003e and our full \u003ca href=\"\/collections\/airline-straps-hardware\"\u003eL-track system\u003c\/a\u003e selection are the fastest way to spec a complete setup. Fittings also accept any standard S-hook strap you already own. Not sure how to lay it out? Give us a call.\u003c\/p\u003e\u003cp\u003e\u003cem\u003ePlease note: this track is intended for cargo securement and recreational use. It is not certified for wheelchair occupant restraint in buses, vans, or other passenger transport vehicles.\u003c\/em\u003e\u003c\/p\u003e","brand":"Fasteners Plus","offers":[{"title":"Default Title","offer_id":46506772889736,"sku":"ATA96AL-AN-4PK","price":342.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0277\/8644\/4936\/files\/anodized-angled-l-track-96-inch-4-pack.01_7c636c64-8c8d-4ed8-a4d9-aca101b6fe1b.jpg?v=1789059616","url":"https:\/\/www.fastenersplus.com\/products\/96-angled-l-track-anodized-finish-4-pack","provider":"Fasteners Plus","version":"1.0","type":"link"}