12" Angled L-Track Kit | Anodized Finish
12" Angled L-Track Kit | Anodized Finish!
12" Angled L-Track Kit | Anodized Finish
Specifications
12" Angled Anodized Aluminum L-Track with Mounting Hardware
This 12" rail is the angled version of standard L-track: the edges slope away from the anchor slots so wheels, casters, and pallet jacks roll across it instead of catching on a square shoulder. That makes it a natural fit in pickup beds, toy haulers, and enclosed trailers where cargo has to move over the track to get where it is going.
Anchor slots run the full length of the rail, so a snowmobile, a lawn tractor, a utility cart, or a stack of construction material can each be tied down at whatever point suits it.
What the Anodizing Buys You
The extrusion is 6061-T6 aluminum, which is light and corrosion resistant on its own. Anodizing goes further: the finish is grown into the surface of the metal rather than sprayed onto it, so there is no coating to chip or peel back from an edge. What you get is a harder face that shrugs off scuffs from loading and unloading, plus better tolerance for sun, road spray, and repeated washdowns than bare aluminum.
Mounting
Mounting holes are pre-drilled on 5" centers, 3 in this piece, sized for 1/4", 6mm, or #12 hardware. A through-bolt with a nut and washer - plus a dab of thread locker - is the most dependable joint. Lag screws or self-drillers into wood or sheet metal will hold, but do not expect bolted-joint strength from them.
This listing ships as a kit: the track plus a matching bolt, nut, and washer pack, so you are not hunting for hardware after the box shows up.
If the length or hole spacing does not suit your layout, the rail cuts cleanly with a carbide-tipped blade in a hacksaw or chop saw, and you can add holes with a carbide countersink bit. Read the welding note below before you take any heat to it.
End caps are available for this profile if you want to close off the cut ends and tidy up the installation.
Do Not Weld It As-Is
Leave the anodizing on and this rail will not weld properly. The finish behaves as an insulator and contaminates the puddle, which leaves a weak and unpredictable joint. If your install genuinely calls for a weld, grind the anodizing off the weld zone and a margin around it first and weld to bare aluminum.
How Much Will It Hold?
We do not publish a single working load limit for the rail, because an installed track is only as strong as the fasteners you picked and the structure you anchored into. The extrusion is made to be at least as strong as the fittings and straps we sell to go with it, which puts the responsibility on the install. If you are unsure what your floor or wall will take, ask your trailer or vehicle manufacturer, and read WSTDA T-5, section 3.4.
Specs
- Length: 12"
- Profile: Angled edge, low-obstruction
- Material: 6061-T6 aluminum, anodized finish
- Mounting holes: 3 holes, 5" centers
- Compatible hardware: 1/4", 6mm, or #12 fasteners
- Quantity: 1 rail plus fastener pack
Finish the System
Track on its own does not secure anything. Pair it with single- or double-stud L-track fittings, L-track straps that clip straight into the slots, or a cargo net for loose gear. Pre-built L-track kits and our full L-track system selection are the fastest way to spec a complete setup. Fittings also accept any standard S-hook strap you already own. Not sure how to lay it out? Give us a call.
Please note: this track is intended for cargo securement and recreational use. It is not certified for wheelchair occupant restraint in buses, vans, or other passenger transport vehicles.
Add the Essentials
Complete your order with these essentials, compatible with:
12" Angled L-Track Kit | Anodized Finish
My Cart:
Add the Essentials
Complete your order with these essentials, compatible with:
12" Angled L-Track Kit | Anodized Finish
My Cart:
-
Smart Angled Edge Design
Features an angled edge design that allows motorcycles, ATVs, utility carts, and other wheeled equipment to roll smoothly over the track. No harsh edges to bump over—just easier loading and unloading. It’s a simple upgrade that makes moving heavy, wheeled cargo faster, safer, and more convenient.
-
Anodized for a Finish That Lasts
Built from lightweight 6061-T6 aluminum, this anodized L Track offers outstanding strength and corrosion resistance. Unlike paint, the anodized finish is embedded into the metal, creating a more durable, scratch-resistant surface that won’t chip or peel.
-
Everything You Need to Secure Your Cargo
Shop L Track SystemsFasteners Plus offers a wide range of fittings & accessories designed to work seamlessly with your L track rails. Explore our selection of L track, fittings, accessories, tie-down straps, and more to complete your L track tie down system.
-
We are on a mission to expand our national reach—offering more product selection and faster delivery times. So far we’ve made remarkable progress in our expansion efforts, effectively doubling our capacity by adding a new 47,000 sq. ft. warehouse in Simpsonville, South Carolina, in addition to our existing 60,000 sq. ft. facility in Urbana, Iowa.
-
We pride ourselves on delivering a user-friendly, high quality experience online and over the phone. Our knowledgeable team of experts is readily available via phone to assist with product questions and custom pricing inquiries. We’re available Monday thru Friday from 7:00 AM – 5:00 PM CST. We look forward to supporting you on your next job.
-
We partner with trusted manufacturers in the fasteners industry to bring our customers a selection of over 10,000 different products. Fasteners Plus is one of only four Certified Platinum E-Commerce Vendors of Simpson Strong-Tie products, one of the largest suppliers of high-quality structural building products in the world.
